Repair of fuel system components VAZ-2106

Details of the engine power system
Details of the engine power system: 1 - carburetor; 2 - warm air intake; 3 - cold air intake; 4 - air filter housing cover; 5 - filter element; 6 - air filter housing; 7 - sensor...

Description of the design of the power system
The power supply system consists of a fuel tank with a level indicator sensor and a fuel reserve, fuel lines, a fuel pump, an air filter and a carburetor. Fuel tank with a volume...

Air filter element — replacement
The air filter element is replaced according to the maintenance interval (see " Periodic maintenance "). When operating the vehicle in dusty and dirty conditions, it is...

Fuel filter — replacement
To perform the work, you will need a container for draining gasoline (0.5 l). Execution sequence 1. We prepare the car for work (see " Vehicle preparation for maintenance and...

Air filter housing — removal and installation
Removing 1. We prepare the car for work (see " Vehicle preparation for maintenance and repair "). 2. We clean the air filter housing from dirt. 3. Using pliers, loosen the clamp...

Fuel pump filter — cleaning
We clean the filter without removing the pump from the car. Execution sequence 1. We prepare the car for work (see " Vehicle preparation for maintenance and repair "). 2. We clean...

Fuel pump — removal and installation
Removing 1. We prepare the car for work (see " Vehicle preparation for maintenance and repair "). 2. Clean off dirt with a rag and wash the outer surface of the fuel pump with...

Fuel Pump Diaphragm — Replacement
Removing 1. We prepare the car for work (see " Vehicle preparation for maintenance and repair "). 2. We clean the dirt with a rag and wash the outer surface of the fuel pump with...

Fuel tank — removal and installation
To perform the work, you will need a special hose and a container for draining fuel. Removing 1. We prepare the car for work (see " Vehicle preparation for maintenance and repair...

Carburetor Fuel Filter — Cleaning
Execution sequence 1. We prepare the car for work (see " Vehicle preparation for maintenance and repair "). 2. We clean the body and plug of the carburetor fuel filter from dirt....

Carburetor drive — check and adjustment
An assistant is required to complete the work. Execution sequence 1. We prepare the car for work (see " Vehicle preparation for maintenance and repair "). 2. Remove the air filter...

Air damper actuator — check and adjustment
Execution sequence 1. We prepare the car for work (see " Vehicle preparation for maintenance and repair "). 2. Remove the air filter housing from the carburetor studs (see " Air...

Idle speed — adjustment
Idling adjustment is made after the repair of the carburetor, as well as in case of unstable idling of the engine. The idling speed of the crankshaft should be in the range of...

Carburetor cover — removal and disassembly
The need to remove the carburetor cover arises when adjusting the fuel level in the float chamber, checking and replacing the needle valve, purging and cleaning the jet channels...

Carburetor — removal and installation
Removing 1. We prepare the car for work (see " Vehicle preparation for maintenance and repair "). 2. Remove the air filter housing from the carburetor studs (see " Air filter...

Carburetor body — disassembly
We disassemble the carburetor body to flush its parts, clean channels, replace defective parts, gaskets and diaphragms. You will need carburetor cleaner or acetone to get the job...

Fuel level in the float chamber — check and adjust
The fuel level in the float chamber is checked when replacing the float, needle valve, or when disassembling the carburetor. The level and supply of fuel necessary for the normal...

Needle valve and float — replacement
Execution sequence 1. Remove the carburetor cover (see " Carburetor cover - removal and disassembly "). 2. With a beard we knock out the float axis from the bracket hole on the...

Starting device — check and adjustment
To perform the work, you will need a template made of thick paper with a width of 5.25-5.75 mm and a piece of wire with a diameter of 0.9-1.0 mm. Execution sequence 1. We prepare...

Pneumatic throttle valve — removal and installation
You can remove the pneumatic drive without removing the carburetor from the car. To do this, just remove the air filter housing (see " Air filter housing - removal and...

Solenoid valve — check and replace
With a faulty solenoid valve, the engine stalls when the pedal is released "gas" and with the carburetor choke fully open. Also, a malfunction can be caused by disconnecting the...