Car ignition system VAZ-21061 «Zhiguli»

The ignition system is designed to ignite the working mixture in the combustion chambers of the engine with a spark discharge in accordance with the sequence of operation of its cylinders. VAZ-2106 cars are equipped with a contact (classic) ignition system, and part a

Contact diagram (classical) ignition systems
Contact diagram (classical) ignition systems 1 - rechargeable battery; 2 - generator; 3 - ignition switch; 4 - ignition coil; 5 - ignition distributor; 6 - spark plugs. The...

Ignition distributor 30.3706 (contact ignition)
1 - roller; 2 - wire for supplying current to the distributor; 3 - capacitor; 4 - locking spring of the cover; 5 - housing of the vacuum regulator; 6 - membrane; 7 - felt; 8 –...

Ignition coil B-117A (contact ignition)
Ignition coil - step-up transformer, converts low voltage pulsed current (12V) into a high voltage current. The coil windings are installed in an aluminum case. Housing cover made...

Switch and spark plugs
Ignition switch Ignition switch - combined, consists of a lock with an anti-theft device and a contact part, assembled in one housing. The switch is installed on the left side of...

Scheme of a non-contact ignition system
Scheme of a non-contact ignition system 1 - ignition switch; 2 - generator; 3 - storage battery; 4 - ignition coil; 5 - switch; 6 - sensor-distributor ignition; 7 - spark plugs....

Sensor-distributor ignition 38.3706 (contactless ignition)
1 - roller; 2 – the case of the gauge-distributor of ignition; 3 - locking spring cover; 4 – contactless sensor; 5 - housing of the vacuum regulator; 6 - diaphragm; 7 – draft of...

Checking spark plugs (contact ignition)
When one of the spark plugs fails, the engine vibrates violently at idle - «troit». With the engine idling, we disconnect the high-voltage wires from the spark plugs one by one....

Checking the operation of the contact ignition system
If the engine does not start with fuel in the carburetor, check the operation of the ignition system. We take out the central high-voltage wire (connected to the ignition coil)...

Replacing spark plugs
Candles are installed in the cylinder head on the left side. Blow the spark plug socket with compressed air from a compressor or pump to remove contaminants. We change the candles...

Adjusting the gap between the electrodes of the spark plug
We check the gap between the electrodes of the candle with a round wire gauge. Convenient special key (designed for maintenance of the ignition system) with a set of necessary...

Adjustment of the angle of the closed state of the breaker contacts
The angle of the closed state of the breaker contacts is determined by a car tester or probe by the size of the gap between the open contacts. Remove the distributor cap. It is...

Checking the ignition timing
It is convenient to check and adjust the ignition timing using a stroboscope (see the operating instructions for the device). In the absence of a stroboscope, we check and adjust...

Ignition timing adjustment
We set the crankshaft to the position of the top dead center of the compression stroke of the piston of the first cylinder (long mark). If the ignition distributor was not removed...

Ignition advance correction
If the ignition timing setting has been violated, check and, if necessary, adjust the ignition timing (see Checking the ignition timing ). To adjust the ignition timing for a...

Replacing the ignition distributor rotor
We snap off the clamps of the ignition distributor cover. We remove the cover. Unscrew the two screws securing the rotor.. ...and take it off. We install a new rotor with a...

Ignition distributor lubrication
Every 20 thousand kilometers, turning the cap, open the oiler filler hole and pour four drops of engine oil into it. Close the hole with a lid. Every 10 thousand kilometers, we...

Replacing the ignition distributor
Removing the distributor cap (see Replacing the distributor rotor ). We remember (or mark) the position of the contact plate of the rotor. Remove the hose from the union of the...

Replacing the ignition coil
The ignition coil is installed in the engine compartment on the left mudguard and secured with two nuts. We take out the high-voltage wire from the coil cover. key «for 8» unscrew...

Ignition distributor repair
Removing the ignition distributor (see Replacing the ignition distributor ). It is possible to measure the characteristics of the vacuum and centrifugal ignition timing...

Repair of the sensor-distributor of ignition
Removing the ignition switch (same as contact distributor, see Replacing the ignition distributor ). It is possible to measure the characteristics of vacuum and centrifugal...

This section is available on russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More articles from other manuals on VAZ cars:
➠ Electrical equipment: Ignition system VAZ-11113 (1996-2003)
➠ Power unit: Ignition system VAZ-21011 (1974-1983)
➠ Electrical equipment: Ignition system VAZ-21051 (1979-2010)
➠ Electrical equipment: Ignition system VAZ-21099 (1990-2004)
➠ Power unit: Ignition system VAZ-21214 (1994-2006)

Share with friends: