Exterior elements of car body VAZ-2110

Car body maintenance
Lubrication of hinges and door stops, cleaning of drainage holes should be performed at each periodic maintenance of the vehicle (every 15,000 km). Door keyholes should be...

Removal and installation of a radiator grille
Removing 1. We prepare the car for repair work. 2. Open the hood and use an 8 mm socket wrench to unscrew the two self-tapping screws of the upper mounting of the radiator grille....

Replacing the gas struts of the hood
Helpful advice. The bonnet gas struts should be replaced one by one. If the stops are so loose that they cannot hold the hood, place some kind of stop under the hood. Removing 1....

Removing the noise insulation of the hood
Helpful advice. To remove the noise insulation of the hood, it is better to use a special tool for removing the noise insulation holders. Removing 1. We prepare the car for repair...

Removal, installation and adjustment of a cowl
You will need an assistant to carry out repairs. Helpful advice. It is better not to remove the gas stops or do it after removing the hood. Removing 1. We prepare the car for...

Removal, installation and adjustment of the lock of a cowl
Removing 1. We prepare the car for repair work. 2. Remove the grille. 3. For the convenience of disconnecting the hood lock cable, we remove the sound signal. 4. Using a 10 mm...

Lubrication and replacement of the hood lock drive cable
To replace the hood lock rod, you will need: assistant; kapron cord at least 5 m long; plastic body of a ballpoint pen; a piece of thin steel wire 10 cm long or a paper clip....

Removal and installation of the air intake grille of the ventilation system
Removing 1. We prepare the car for repair work. 2. Remove the battery. 3. Remove the decorative plastic cap of the left wiper arm nut. 4. Using a 10 mm spanner, unscrew the lever...

Removal, installation, replacement of the front fender liner
Note. Removal, installation, replacement is shown on the example of the left wing liner. To carry out repairs, you will need: jack; stand. Removing 1. We prepare the car for...

Removal, installation, replacement of the front bumper
To carry out repairs, you will need: assistant; viewing hole or flyover. Removing 1. We prepare the car for repair work. 2. Remove the grille. 3. We turn off two screws securing...

Removal, installation, replacement of the threshold lining
Removing 1. Remove the mudguard of the front wing. 2. Using a Phillips screwdriver, unscrew the self-tapping screw of the front fastening of the decorative sill trim. 3. We turn...

Removal, installation, replacement of the front wing
Removing 1. Remove the front fender liner. 2. Remove the front bumper. 3. Remove the decorative door sill. 4. Turn off with an 8 mm socket wrench: A) self-tapping screw of the...

Removal and installation of engine protection
To perform work on removing the engine protection, an inspection hole or overpass is required. Note. Engine protection is fixed in front - with five nuts (1), from the sides with...

Removal and installation of a mudguard of a motor compartment
Note. The work is shown on the left panel. The right shield is removed and installed in the same way. To carry out repairs, you will need: jack; stand. Removing 1. We prepare the...

Removal and installation of a lateral rear-view mirror
Notes: The work is shown on the example of the left front door. All equipment of the right front door can be removed and installed in the same sequence. Cars of recent years of...

Removal and installation of the gas tank hatch
Removing 1. Cross-tip collar (or Phillips screwdriver) unscrew the two screws securing the hatch to the body and remove the hatch. Installation We install the gas tank hatch on...

Removal and installation of a back bumper
Note. The work is shown on a VAZ 2112 hatchback car. On a VAZ 2110 car with a sedan body, the bumper has the same attachment points. The bumper of a VAZ 2111 car with a station...