Unscrew the screws securing the armrest, after removing the decorative plastic plug 2 (pic. 8-13) top screw, and remove the armrest.
Pic. 8-13. Interior view of the front door: 1 - lower armrest mounting screws; 2 - plug of the upper armrest mounting screw. The arrows show the location of the door upholstery holders
Press socket 20 (pic. 8-14), remove retaining spring 1 using tool 2 А.78034 and remove window lifter handle 22.
Pic. 8-14. Sliding window drive: 1 - retaining spring; 2 - tool A.78034 for removing the retaining spring; 3 - power window mechanism; 4 - cable; 5 - top roller; 6 - sliding glass; 7 - holder of the sliding glass: 8 - cable holder; 9 - cable clutch; 10 - glass holder bracket; 11 - lower roller; 12 - tension roller 13 - power window mechanism housing, 14 - drum with driven gear; 15 - drive gear: 16 - support of the drive roller; 17 - brake spring; 18 - spring brake leash; 19 - housing cover; 20 - socket; 21 - drive roller; 22 - power window handle
Note. Since 1990, window handles have been installed from the VAZ-2105 car. To remove the window regulator handle, it is necessary to move the handle lining until it exits the groove of the roller.
Prying off the lining of the inner handle of the lock drive with a screwdriver, remove the lining.
Overcoming the resistance of spring plastic holders (in fig. 8-13) marked with arrows, remove the door trim.
With the sliding window in the up position, remove the mounting screws and remove the front and rear guide grooves of the sliding window.
Lower the glass down, loosen the power window tension roller nut, disconnect the cable from the lower glass clip, remove the cable from the rollers and remove the glass through the lower door opening. Loosen the mounting nuts and remove the power window mechanism.
Remove the sliding window seal and turn glass assembly by unscrewing the mounting screws.
Unscrew button 6 (pic 8-15) lock, unscrew the screws securing the bracket 4 of the inner handle 1 of the lock drive, unscrew the screws 3 (pic. 8-16) fixing the lock body and remove the lock with rods, having previously disconnected the rod 20 (see fig. 8-15) from the lock switch.
Pic. 8-15. Left front door lock: 1 - inner drive handle female, 2 - lining of the inner handle; 3 - axis; 4 - bracket for the inner handle; 5 - thrust of the inner handle; 6 - lock lock button; 7 - thrust of the lock button; 8 - lever. internal lock drive; 9 - lock case; 10 - cracker spring; 11 - cracker of the lock retainer; 12 - rotor; 13 - support of the central roller; 14 - latch body; 15 - external drive lever; 16 - spring of the external drive lever; 17 - ratchet 18 - ratchet spring; 19 - roller off the lock; 20 - thrust off the lock; 21 - lock lever
Pic. 8-16. Front door lock fixing: 1 - lock lock button; 2 - thrust of the lock button; 3 - lock fixing screws
Remove the outer door handle by unscrewing the two fastening nuts.
Turn out two bolts of fastening and remove the limiter of opening of a door.
Assemble the front doors in the reverse order of disassembly.
When installing the power window, make sure that the coils of the cable on the drum do not overlap. Adjust cable tension 2 (pic. 8-17) and smooth operation of the power window by moving the tension roller, loosening the nut 3.
Pic. 8-17. Power window cable tension adjustment: 1 - holder of the sliding glass; 2 - cable; 3 - tension roller bolt nut
Before installing the door upholstery, check the condition of the plastic upholstery holders.